ABS Pumps - ABS Submersible sewage Pump AFP 0831 - 2046

Type key Example: ABS AFP 1035.3 ME 250/2 Ex
AFP
 Submersible Sewage Pump
10 Discharge outlet DN (cm)
35
 Hydraulic number
.3
 Impeller
Motor:  
ME M = Modular motor version;
E = High efficiency
15 Motor power P2 kW x 10
4 Number of poles
Ex
 Explosive-proof
Properties:  
Flow up to: 750 m³/h
  Head, max 65m
Head, Max: 65m

ABS AFP 0831 - 2046 - Submersible sewage Pump

ABS AFP range robust, reliable submersible pumps from 1.3 to 30 kW for pumpingwastewater and sewage from buildings and sites in private, commercial, industrial and municipal areas in accordance with
EN 12050-1. Available as standard AFP or as higher specification AFP(K).

Applications

AFP submersible pumps have been designed for the economic and reliable pumping of clear or wastewater, gaseous liquids, and for sewage and sludge, in fixed or portable applications.
  • For fixed, wet well applications the AFP is pedestal mounted. Using a self-sealing coupling system the pump seals automatically on the pedestal when lowered by guide rail into position.
  • Dry well applications have the option of horizontal or vertical installation.
  • With vortex hydraulics the AFP is particularly suitable for sewage, abrasive matter, and fluids containing stringy materials that tend to ”rope”.
  • The Contrablock hydraulic system offers higher efficiency and is suitable for larger proportions of solid or fibrous matter.

Construction

The water-pressure-tight, encapsulated, fully flood-proof motor and the pump section form a compact, robust, modular construction. Maximum allowable temperature of the medium for continuous operation is 40 °C (information on applications at other temperatures available on request). Available in explosion-proof versions in accordance with international standards EExd II BT4, FM and ATEX.

Cooling

AFP: Free-circulation cooling by the medium.
AFP(K): Closed loop cooling system with circulation of glycol and water which has no contact with the sewage being pumped. This optimises heat exchange and avoids the danger of blockage of the cooling system with sewage particles.
Dry installation is possible without cooling system, for intermittentuse only and subject to strict limitations.

Bearings

The stainless steel motor shaft is supported in lubricated-for-life ball bearings.

Shaft sealing

Between the motor and hydraulic section is by means of a high quality, silicon carbide, double mechanical seal. Standard AFP has a single mechanical seal and upper lip seal. AFP(K) has the option of double mechanical seals or a seal cartridge. The seal cartridge combines both mechanical seals into a complete, easy-to-replace unit (not available with ME motor). All seals are independent of rotation direction and resistant to temperature shock.

Discharge

DN 80, 100, 150 and 200 DIN flange.

Temperature monitoring

TCS (Thermo-Control-System) with thermal sensors in the stator to switch off the pump in the case of overheating and switch on automatically after cooling down.

Seal monitoring

DI system consisting of a sensor in the motor and oil chambers which signals an inspection alert if there is leakage at the shaft seals (not in oil chamber on Ex version).

Hydraulics

AFP 0831-0835, 1031-1035, 1533: vortex, open, recessed, four-vane impeller.
AFP 0841-0844, 1041-1049, 1541, 1543 & 2045: Contrablock, open single-vane impeller.
AFP 1546 & 2046: Contrablock, open double-vane impeller.

Motor

Three-phase, 400 V, 50 Hz, squirrel-cage motor as 2-pole (2900 r/min), 4-pole (1450) and 6-pole (980). Protection type IP 68, with stator insulation Class F (155 °C) for standard AFP or Class H (180 °C) for AFP(K) version. Direct starting up to 3 kW; from 4 kW star-delta or direct starting is possible. Motors with other operating voltages and frequencies are also available.

Features

  • High-efficiency hydraulic design using Contrablock or vortex impellers.
  • Available as standard AFP or higher specification AFP(K).
  • AFP(K) has class H insulation and double mechanical seals as standard, with options of seal cartridge and closed loop cooling system.
  • Available as explosion-proof.
  • Designed for fixed or transportable installation.
  • For lifting, AFP has cast eyelet, AFP(K) has stainless steel lifting hoop.

Materials

Description

Material
Motor Housing
 Cast iron EN-GJL-250
Motor Shaft
 Stainless Steel 1.4021 (AISI 420)
Volute, Impeller, Bottom plate
 Cast iron EN-GJL-250
Fasteners Stainless Steel 1.4401 (AISI 316)

 
AFPP(K) options: stainless steel motor shaft 1.4401 (AISI 316), stainless steel impeller 1.4460 (AISI 329), viton seals, and surface hardened cast iron impeller and bottomplate.
AFP is available in SX version as a complete stainless steel pump (see separate literature).

Downloads

 

Should you require further information regarding any of the products or services we offer, or to arrange a sales appointment, call: 020 8991 6650 or e-mail sales@spse.co.uk

Please take time to take a look at our informative website, which incorporates an on-line storage calculator, Case Studies, GRP pump station (budget-price) calculator along with extensive downloadable technical leaflets. 

If you have a pump station application you will need to have certain information available for us to quote by complete our online pump station enquiry form this will enable us to provide you with a proposal our proposals are normally turned around within 24hrs. Click here for further guidance; please remember to complete all fields.

Alternatively if you would like one of our experienced friendly team to make contact with you, please click here and complete the contact details at the bottom of the page then click submit, we will call you back within two hours during normal working hours.

 

ABS Pumps Product Links

ABS Pumps Only

ABS Pumps Lifting Stations

More Links


Resources

Contact